Can I Set Up a Tub Myself? Considerations And Also Steps

Request Your Service

Were you in search of insight about Installing A Bathtub?


Installing A Bathtub
Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, woodworking, and also often, tiling abilities. Changing an old tub with a new one is likewise a moderately hard task. If the old bathtub is easily easily accessible, the job can move rapidly; if you have to open a wall to get rid of the old bathtub as well as place the new bathtub, the task is a lot harder. In either situation, the project is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub as well as embeded in the new one. Make sure you have actually qualified yourself for the work as well as fit trying it. Rather than working with a specialist to take over a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will help you set up a brand-new bathtub in your washroom if you have currently purchased a brand-new tub and also don't require to alter the plan of your previous water supply pipes.
Your devices and product checklist must comprise the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is often the situation.
    Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
    Prior to moving on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipes.
    If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in location in between the faucet as well as the sink. Protect the faucet in place with the maker supplied backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former type needs to be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.

    Mounting the Bathtub


    Using both wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
    The following objective is to make certain that the tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub up until the spirit level reviews degree.
    To install faucets, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the various other faucet.
    Switch on the water as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub as well as also inspect the overflow electrical outlet as well as the typical outlet for leakages.
    Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait until the bathtub has actually been used at the very least once as this will certainly settle it right into its final placement.

    Getting ready for the Installment


    First of all, the sustaining framework provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to avoid pressure on the bath tub.
    Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its last placement.

    Tiling Around the Bath tub


    In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, causing the water to permeate the wall between the bath as well as the tiling, leading to issues with wetness as well as possible leaks to the ceiling below.
    You can select from a range of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can break fairly early if you do not take into account this activity prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently readily available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water-proof sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    I hope you enjoyed reading our post about A Step-by-Step Guide to Installing a Bathtub. Thank you for taking the time to browse our content. Sharing is good. Who knows, you may be helping someone out. I enjoy reading our article about Installing A Bathtub.




    Book With Us Today!


    Leave a Reply

    Your email address will not be published. Required fields are marked *